Відео

Ive seen a huge difference in chains even using the same saw. I see that Husky even has an aftermarket bar. So hard to make a fair comparison even if the saws had the same HP. You'd have to use new air filters, new spark plugs, autotune or manually tune each saw to optimal conditions, use the same amount of downward pressure on both saws, use wood that was exactly the same with no knots, make about 10 cuts each and use an average, on and on...

Next up... 500i vs 592xp!!!!!!! 😂

Would you pick the 395xp over these two?

Sthil a piece of junk

Long story short, over the years I've accumulated more 2t oils than I can possibly use up in the next 5 years. For 2t's (saws, trimmers, blowers and generators) I've pretty much narrowed it down to hp2, saber, red armor and k2 in no particular order at 32-40:1. My question is regarding 4-mix. I've been sticking with motomix and/or hp ultra at 40-45:1 yes, I add additional hp ultra to the motomix. Do you see hp2, saber, red armor or k2 at 32-40:1 as a potential problem in 4-mix engines? Or suggest I stay with a separate hp ultra mix for them?

I have a poulan 4000 it still run as it should mean saw . I was told the cut 10 cc above there cc level !!

very important

Compare this stihl with husqvarna 579. Will it be fair enough?

I like both stihl and husky, but that 500i for so many cc plus the saw is so lite, only reason I would lean towards husky is that I can get heated handles and I do like the gap heated handles, bu both are very good saws

Works great. You can screw the wood screw in by hand, and it will give enough bite to pull the plugs. My hobby knife for the tabs, and the thing looks new. Plus, now I have to learn to tune this thing.

7310 guy here.

I have a ms261,bought it a year ago. I like your idea and might try it. What did you use to cut slots in muffler? Also does the ms261 have a spark arrestor? If so is it easily removed?

Teniendo en cuenta la cilindrada y la potencia me quedo con la husqvarna gracias por compartir

The 572 ported is a greay saw if you can afford it. Most guys port them.

Husky all day and ported they are mental.

What size tsumura bar is that?

If the 572 had a muffler mod it would probably beat the pants off that 500i. They are both bad ass saws but price and size .... Well, you know

Where do you get these products?

Do you just rotate the flywheel back and forth to make sure it’s at tdc? Just keep wiggling until the valves don’t move?

Tell me the best oil for low ambient temperatures, for MS 661.

the 572 is supposed to wake up after some decent use

That's Brad Snellings method. He originated it about 13 years ago!

Both are great saws, go with the better dealer near you.

If polybutane based oil + solvent has high film strength at 100 C, does it have low film strength at low temperature = cold start?

Where can I find a Poland 5200 counter vibe chainsaw? Can I find one on eBay?

Stihl junk under lisc to china.

What is your reason for not recommending Yamalube any more? I use 2R is my saws quite a bit, so always keen to hear other peoples experiences.

Just got the OTT tune on my '21 Tacoma and noticed the same thing. Better response, smoother running, and much less engine noise. Good upgrade!

Já me escrevi no canal gostei do vídeo

I’m looking at the STIHL 2024 POWER TOOLS & ACCESSORIES booklet I received from my local dealership. On page 51 center right on that page it clearly states “STIHL ROLLOMATIC ES LIGHT” “…up to30% lighter than the STIHL ROLLOMATIC E…”. If that is not true, then it is a lie. It does not say, only on long bars, or only if you replace your shorter bar with a longer bar, or only if weighing on the moon, it says 30% lighter. A 20” bar is not a short bar, but it definitely is not a long bar, but additionally, 30% is 30% no matter what the volume.

I just bought a new Stihl Rollomatic ES Light to replace my original Stihl Rollomatic E Standard bar for my Stihl MS 362 C-M. I was really looking forward to adding a 30% decreased weight to an already light saw further increasing the power to weight ratio of this beast of a chain saw. So I get the new light bar and immediately weigh the bare bar on my wife’s kitchen food scale, with the light bar coming in at 32.9 ounces. So then I go to the shed and change out the new bar for the old, clean up the old bar real good, because I’m going to be weighing it on my wife’s food scale, and it comes in at 36.0 ounces, a whopping 3.1 ounces lighter, or an unimpressive 10%. Now I ask myself, why did I just pay $148, three times as much as I could have for a Standard bar, to save a mere 3.1 ounces? I was expecting the bar to be 30% lighter, which would have been about a 25 ounce bar. Stihl, you lied to me!

a ported cs680 is a great 1 saw bag. you can easily get just over 1 more hp and they are torque beast across the whole rpm range

Got a 572/bullet proof. Next

Clear view thanks. But price is always high

What yr is that.

Link for the dogs please

What ratio should I mix motul 710 in a ms 261c? 40:1 or 50:1?

Does it damage a 2 stroke engine to shut the fuel off and run it til it stops running? Thanks.

Stihl rule

I’ll send 3 running 10-10’s for that poulan lol they’re not the most reliable but good saws maybe try the 605/610 series they’re very underrated but very powerful.

What if I mix some Lucas with yamalube how about mercury marine premium quicksilver

Just mix them all together and make a super blend like I do at the Slurpee machine

Next will be a splitter video?? 😉

Cool video!

I've got around 8-10 cord here to split, and it just keeps piling up. I told my boy and wife early last week we are moving into splitting mode, so I started making preparations for that. Unfortunately I planned on starting Friday and it was raining all day after we finished up a storm damaged cherry removal. Tomorrow evening looks great though, 54 and clear. Have a great day.

A viewer of Bjarne i see.👍

how about royal purple 2 stroke oil , do u like

🪵🪵🙏🙏

I switched to echo because their warranties are better, they are cheaper to repair…i brought my 576xp into the dealer…took them a week and a half to tell me “i need a new carburetor”…didnt tell me what was wrong with the carb…just that i needed a new one…that thing only ran non ethanol…with red armor…and it was 6 years old…probably 30 hours on it total… The autotune carbs are $150…standard carbs are $50….$150 to install, so, $300 to replace a carb….$1100 saw…

Yes, it works with short bars, for longer bars, keep the 7, for a couple story.